diff --git a/Documentation/devicetree/bindings/net/btusb.txt b/Documentation/devicetree/bindings/net/btusb.txt
new file mode 100644
index 0000000000000000000000000000000000000000..2c0355c859723418ecd57f291dfd672804e1cdc4
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/btusb.txt
@@ -0,0 +1,40 @@
+Generic Bluetooth controller over USB (btusb driver)
+---------------------------------------------------
+
+Required properties:
+
+ - compatible : should comply with the format "usbVID,PID" specified in
+ Documentation/devicetree/bindings/usb/usb-device.txt
+ At the time of writing, the only OF supported devices
+ (more may be added later) are:
+
+ "usb1286,204e" (Marvell 8997)
+
+Optional properties:
+
+ - interrupt-parent: phandle of the parent interrupt controller
+ - interrupt-names: (see below)
+ - interrupts : The interrupt specified by the name "wakeup" is the interrupt
+ that shall be used for out-of-band wake-on-bt. Driver will
+ request this interrupt for wakeup. During system suspend, the
+ irq will be enabled so that the bluetooth chip can wakeup host
+ platform out of band. During system resume, the irq will be
+ disabled to make sure unnecessary interrupt is not received.
+
+Example:
+
+Following example uses irq pin number 3 of gpio0 for out of band wake-on-bt:
+
+&usb_host1_ehci {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mvl_bt1: bt@1 {
+ compatible = "usb1286,204e";
+ reg = <1>;
+ interrupt-parent = <&gpio0>;
+ interrupt-name = "wakeup";
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 699b2dbaf75b2e44b7bcabab7fbfecd00bf7d5b4..f6bf990ccaeb1377603ab029c6eb5fcdfe0b8f1d 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -24,6 +24,8 @@
#include <linux/module.h>
#include <linux/usb.h>
#include <linux/firmware.h>
+#include <linux/of_device.h>
+#include <linux/of_irq.h>
#include <asm/unaligned.h>
#include <net/bluetooth/bluetooth.h>
@@ -373,6 +375,7 @@ static const struct usb_device_id blacklist_table[] = {
#define BTUSB_BOOTING 9
#define BTUSB_RESET_RESUME 10
#define BTUSB_DIAG_RUNNING 11
+#define BTUSB_OOB_WAKE_ENABLED 12
struct btusb_data {
struct hci_dev *hdev;
@@ -420,6 +423,8 @@ struct btusb_data {
int (*recv_bulk)(struct btusb_data *data, void *buffer, int count);
int (*setup_on_usb)(struct hci_dev *hdev);
+
+ int oob_wake_irq; /* irq for out-of-band wake-on-bt */
};
static inline void btusb_free_frags(struct btusb_data *data)
@@ -2732,6 +2737,66 @@ static int btusb_bcm_set_diag(struct hci_dev *hdev, bool enable)
}
#endif
+#ifdef CONFIG_PM
+static irqreturn_t btusb_oob_wake_handler(int irq, void *priv)
+{
+ struct btusb_data *data = priv;
+
+ pm_wakeup_event(&data->udev->dev, 0);
+
+ /* Disable only if not already disabled (keep it balanced) */
+ if (test_and_clear_bit(BTUSB_OOB_WAKE_ENABLED, &data->flags)) {
+ disable_irq_nosync(irq);
+ disable_irq_wake(irq);
+ }
+ return IRQ_HANDLED;
+}
+
+static const struct of_device_id btusb_match_table[] = {
+ { .compatible = "usb1286,204e" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, btusb_match_table);
+
+/* Use an oob wakeup pin? */
+static int btusb_config_oob_wake(struct hci_dev *hdev)
+{
+ struct btusb_data *data = hci_get_drvdata(hdev);
+ struct device *dev = &data->udev->dev;
+ int irq, ret;
+
+ clear_bit(BTUSB_OOB_WAKE_ENABLED, &data->flags);
+
+ if (!of_match_device(btusb_match_table, dev))
+ return 0;
+
+ /* Move on if no IRQ specified */
+ irq = of_irq_get_byname(dev->of_node, "wakeup");
+ if (irq <= 0) {
+ bt_dev_dbg(hdev, "%s: no OOB Wakeup IRQ in DT", __func__);
+ return 0;
+ }
+
+ ret = devm_request_irq(&hdev->dev, irq, btusb_oob_wake_handler,
+ 0, "OOB Wake-on-BT", data);
+ if (ret) {
+ bt_dev_err(hdev, "%s: IRQ request failed", __func__);
+ return ret;
+ }
+
+ ret = device_init_wakeup(dev, true);
+ if (ret) {
+ bt_dev_err(hdev, "%s: failed to init_wakeup", __func__);
+ return ret;
+ }
+
+ data->oob_wake_irq = irq;
+ disable_irq(irq);
+ bt_dev_info(hdev, "OOB Wake-on-BT configured at IRQ %u", irq);
+ return 0;
+}
+#endif
+
static int btusb_probe(struct usb_interface *intf,
const struct usb_device_id *id)
{
@@ -2853,6 +2918,11 @@ static int btusb_probe(struct usb_interface *intf,
hdev->send = btusb_send_frame;
hdev->notify = btusb_notify;
+#ifdef CONFIG_PM
+ err = btusb_config_oob_wake(hdev);
+ if (err)
+ goto out_free_dev;
+#endif
if (id->driver_info & BTUSB_CW6622)
set_bit(HCI_QUIRK_BROKEN_STORED_LINK_KEY, &hdev->quirks);
@@ -3065,6 +3135,9 @@ static void btusb_disconnect(struct usb_interface *intf)
usb_driver_release_interface(&btusb_driver, data->isoc);
}
+ if (data->oob_wake_irq)
+ device_init_wakeup(&data->udev->dev, false);
+
hci_free_dev(hdev);
}
@@ -3093,6 +3166,12 @@ static int btusb_suspend(struct usb_interface *intf, pm_message_t message)
btusb_stop_traffic(data);
usb_kill_anchored_urbs(&data->tx_anchor);
+ if (data->oob_wake_irq && device_may_wakeup(&data->udev->dev)) {
+ set_bit(BTUSB_OOB_WAKE_ENABLED, &data->flags);
+ enable_irq_wake(data->oob_wake_irq);
+ enable_irq(data->oob_wake_irq);
+ }
+
/* Optionally request a device reset on resume, but only when
* wakeups are disabled. If wakeups are enabled we assume the
* device will stay powered up throughout suspend.
@@ -3130,6 +3209,12 @@ static int btusb_resume(struct usb_interface *intf)
if (--data->suspend_count)
return 0;
+ /* Disable only if not already disabled (keep it balanced) */
+ if (test_and_clear_bit(BTUSB_OOB_WAKE_ENABLED, &data->flags)) {
+ disable_irq(data->oob_wake_irq);
+ disable_irq_wake(data->oob_wake_irq);
+ }
+
if (!test_bit(HCI_RUNNING, &hdev->flags))
goto done;